Can be applied on: 
- Mineral-based decorative finishes for interiors;
- Non-mineral decorative finishes with a porous and absorbent surface for interior environments;
Application on particularly matte surfaces may alter their visual appearance and gloss level. 

Binder type: a compound of polyethylene and paraffinic waxes in emulsion.
Bulk density: 
Cera Wax Gold, Silver, Bronze: 1.00 +/- 0.05 g/ml 
Cera Wax Plus: 0.93 +/- 0.05 g/ml 
- Packaging viscosity: thixotropic paste;
- Drying (at 25°C and 65% relative humidity): touch-dry in 30 minutes, recoatable after 4 hours, fully dry after 12 hours, depending on the type of substrate, its absorbency, and environmental conditions.

Cera Wax: ready to use. For site requirements or visual appeal, Cera Wax GOLD, SILVER, BRONZE can be diluted with up to 100% water depending on the desired degree of finish.
Cera Wax PLUS is a ready-to-use product and should not be diluted. 

Mix the material properly before applying. Do not apply onto fresh substrates: wait for the applied coatings to dry completely.
To clean surfaces decorated with Cera Wax, use a dry fabric cloth.

(Referred to environmental conditions T=25° C, RH=60%) 
The surface must be dry and free of dust and salt stains from moisture.

Wait at least 8 hours to make fine trowel finishes and at least 24 hours for multi-layer decorations with a dry film thickness of more than 2 mm.

On surfaces treated with the interior decorative products from the Minerals range, apply a coat of Cera Wax with a microfibre cloth or glove, working the surface with circular movements. 
Wait a few minutes and wipe the surface with a clean glove or cloth, removing any material build-ups.

Cera Wax can also be applied with a sponge-pad, taking care to avoid excess and build-up. We recommend always using a cloth to wipe the surface while still fresh to remove excess wax.

For greater protection, or a more uniform appearance, a second coat of Cera Wax PLUS can be applied after at least 2 hours, following the procedure described above. Wait a few minutes and wipe the surface with a glove or microfibre cloth without product, removing any build-up of material.

When applying, the material must be protected from the cold and from big heat changes during the entire application process.
Do not apply at air, substrate, and product temperatures that are below 5° C or above 35° C, nor in direct sunlight, nor on overheated surfaces (even if already in the shade). Ambient humidity must be < 75%; background  humidity must be < 10%.
It is good practice to always use material from the same batch of manufacture. When using different production batches, we recommend mixing them together to avoid slight differences in tone. For works where, due to non-controllable events, you must continue with a new batch. Do not try to join colours on the same surface and use any breaks in surface-continuity (mouldings, edges, etc.) to create the join.
Please read the relevant technical data sheet carefully for correct materials-use, dilution and laying/application.
We always recommend correctly using proper equipment, and PPE (Personal Protective Equipment) during all preparation and applications stages of substrates and products.

With water, immediately after their use.

7-20 m2/l, per single layer, depending on the type of substrate and its absorption. We recommend checking actual yield by making a preliminary test on the specific background.

Gold, Silver, Bronze, neutral Wax Plus.

1 l; 2.5 l bottles for Cera Wax Plus.
1 l bottles for Gold, Silver, Bronze. 

Maximum temperature for storage stability: +30 °C
Minimum temperature for storage stability: +5 °C
The product should be preferably used within 2 years from date of manufacture when stored in original unopened containers and in appropriate temperature conditions.

EU limit value (Dir. 2004/42/EC)
Cat. A/l: decorative effect coatings (water-base): 200 g/l (2010)
The product contains max: 200 g/l VOC

Use the product according to current health and safety regulations; after use, do not discard the containers in the environment; allow the residue to dry thoroughly, then treat as special waste. Do not dispose of residues in the sewers, waterways or ground. For more information consult the safety data sheet.